Apexi AVC-R Electronic Boost Controller Set-up procedure . Fm AVC-R = White to ECU – pin 9 = Speed Sensor. Here is a link to the AVC-R Manual Link. How to Install and Tune an AVC-R Boost Controller. By Azeem The supplied installation instructions aren’t bad, follow the FD specific instructions EXACTLY. Today we’ll be showing you how to setup the Apexi AVC-R, ease of adjustment similar to a manual boost controller, this proved to be far from.

Author: JoJoshicage Zuluk
Country: Lesotho
Language: English (Spanish)
Genre: Video
Published (Last): 5 January 2009
Pages: 166
PDF File Size: 19.46 Mb
ePub File Size: 12.76 Mb
ISBN: 524-7-79672-421-7
Downloads: 25593
Price: Free* [*Free Regsitration Required]
Uploader: Dajinn

Choose 1 for the slowest response, and 9 for the fastest ressponse. Cut the two connectors from the stack of wires to make it easier to route the wires through the grommet and later solder and heat shrink them back together. This is how the unit knows what gear manial are in.

A guide to fitting and setting up the Apexi AVC-R By aaddzzManua 28, in Electronics avcr avc-r set up guide tutorial apexi wiring settings. These connections should give you correct readings for all the monitors: If you want to do this, two words: Posted July 4, You can display avvr monitored values in many different ways, bars, graphs and old school style gauges can be displayed on the LED screen.

The content is user-generated from passionate Supra enthusiasts.

A guide to fitting and setting up the Apexi AVC-R – Electronics – UK Starlet Owners

Posted February 28, Also, pick the lowest value that holds desired boost Run a line from the bottom of the manuual flange side to a feed from the boost system typically the little manua on the turbo. Nice write up mate. I turned learn-mode OFF in all gear, this is ‘X’ for all gears. Peel back some of the plastic covering to reveal the wires and give you space to splice into the wires.


To make it easier I cut all of the connectors off and then ran the wires through the bulkhead from the inside. Manuall with low duty cycle values and increase the duty values until boost is reached. Next you need to match up your wiring to the diagrams below by splicing into the wire using scotch locks.

Traditionally the AVC-R is used by front wheel drive enthusiasts, trying to limit the boost and power in early gears until the vehicle is up to speed. This is nice if you find boost spikes or loss of boost in a particular gear or speed range. Spexi run the car hard, and try to hit max boost.

New avc-r install instructions & basic tuning –

Posted March 2, You should get close to 9psi I had to reduce my boost, but most everyone else I talked to only need to reduce duty cycle. To save a lot of writing, I’m just going to put this link in You need to be a member in order to leave a comment. So no point wiring in the GREY wire. Now pick a setting, A or B Pretty much works like presets on a radio.

This product is probably one of the biggest items we are asked about from the Apexi lineup, outside of the Super AFC. Do this ’til you get it just right…and hit 1.

After you have wired them in, plug the connectors back in, connect the head unit, tidy up your wires etc and mount the unit Better turbo response and ability to monitor thing you really know noting about. This menu allows you to set the boost levels as well as the Apedi values that you determine.

Have any questions on this mode?

Leave them below for us. The main page features opinions and helpful articles from many Supra owners.


Run a line from COM to the nipple on the actuator. Cut the line from step 2 and insert manyal T-piece, and run a line to NC.

How To Setup Your AVCR

Initialize is the factory reset button, only use this when first setting up your Apexi AVC-R or when you need to wvcr it back to the factory form. Put the car up on and remove the right front tire and the plastic fender. The way to use this value really depends on the boost problems you are having with your AVC-R. Apexl not entirely sure if it makes a difference, but do it anyway just to be sure lol! As you learn the unit’s functions and capabilities, you will eventually master it…but start off simple.

What you’ll need; AVC-R headunit. The AVC-R has been enjoyed by several people, mznual the release of this item came during a time when many enthusiasts were moving away from electronic boost controllers.

Mine is mounted on the fender wall near the ABS unit.

Monday, December 31, Run a line from COM to the top of the wastegate. Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up for a new account in our community. Sign up for a new account in our community. Cut the line in step 1, and insert a T-Piece and run another line to the map sensor. Dialing out the spike perfectly takes a LOT of time Register a new account.

Few companies have stuck by their guns and built quality manhal Apexi has, and now they are celebrating their 22nd year of existence, founded originally in Japan in