ASTM D R_信息与通信_工程科技_专业资料。Designation: D – 05 (Reapproved ) Standard Test Method for Film. ASTM A/AM Steel, Sheet and Strip, Heavy-Thickness Coils, Hot- Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy. ASTM: D ECCA: T4. BS EN: ISO: JIS: K Standard supply includes: Pencil Hardness Tester Block. Set of 20 pencils (9B to 9H).
|Published (Last):||4 December 2012|
|PDF File Size:||18.70 Mb|
|ePub File Size:||3.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
This is related to the low thickness and the high deposition temperature of these coatings as compared with other TiN layers.
ASTM D – 05()e2 Standard Test Method for Film Hardness by Pencil Test
K Standard supply includes: The pencil is held? This test method has also been used to determine the cure of these coatings, especially when forced dried using heat.
It should be recognized that the results obtained may vary between different laboratories when different pencils as well as panels are used. This compressive state is much stronger than unstressed glass and can also be induced chemically by ion exchange on the surface. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Work Item s – proposed revisions of this standard.
ASTM D3363 – 05 PDF
Last previous edition approved in as D — NOTE 1—The operator must watch closely for cutting into or scratching the? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Pencil scratch testing device. ISO Determination of? The panels used, the curing conditions, and the age of the coating prior d336 the test shall be within the limits agreed upon between the purchaser f3363 the seller.
Other advances include antimicrobial and anti-smudge screens. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International D363. Historical Version s – view previous versions of standard. Even though surface-modified nanoparticles d33363 utilized in nanocomposite hard coatings, coatings often result in poor scratch resistance if nanoparticles are not homogenously distributed in the hybrid matrix. Precision and Bias 9.
The modification of polyester resins based on cotton seed oil, linseed oil, soybean oil and sunflower oil with vinyl toluene to improve clarity is also described in the literature. Buy x Banner Ads.
The moment new editions of the standards you monitor are released, changes are made, or appendixes are published, you will be alerted by email. The flame-retardant epoxy thermoset is also possible to obtain by using tetrabromobisphenol-A or phosphate-based aromatic diol in the preparation of epoxy or flame-retardant hardener. Current specialized glass can be produced with a hardness close zstm sapphire, which is 9 on the Mohs scale of hardness compared to 7 for standard glass.
It should be recognized that the results obtained may vary between different laboratories when different pencils as well as panels are used. American Society for Testing and Materials. This service is not available if you are a URL user where you do not log in with an email address.
For mechanical pencil holders with drawing leads, see Fig. The process is started with the hardest pencil and continued down the scale of hardness to either of two end points: Any defacement of the? There is significant competition to produce the thinnest, toughest glass for smartphones and tablets. The benefits of a subscription: A number in parentheses indicates the year of last reapproval. The exterior durability, weather resistance, drying and mechanical properties of these resins are considerably enhanced.
Vegetable oil-based polyesters N. In Building Materials in Civil Engineering However, it is not clear whether the apparent increase in critical load with astm d 05 thickness represents a real astm d 05 or a decrease in adhesion.
Decorative materials are mainly used as facing for the inside and outside walls of buildings, columns, floors, and ceilings.
Set of 20 pencils 9B to 9H. Significant improvement in the drying time and weather resistance properties of dehydrated castor oil-based polyester resin was obtained by graft copolymerisation with methyl methacrylate and butyl methacrylate.