DIN 41494 PDF

Buy DIN () Mechanical Structures For Electronic Equipment; Mechanical Structures Of The ,6 Mm (19 Inch) Series; Components On Front . DIN Mechanical structures for electronic equipment; mechanical structures of the ,6 mm (19″)series; components on front panels; mounting. Category:DIN Good pictures. Advanced All images; Featured pictures; Quality images; Valued images; In this category and in In this.

Author: Zolocage Tojagrel
Country: Madagascar
Language: English (Spanish)
Genre: Travel
Published (Last): 1 September 2006
Pages: 341
PDF File Size: 17.2 Mb
ePub File Size: 6.90 Mb
ISBN: 344-1-66575-451-9
Downloads: 21399
Price: Free* [*Free Regsitration Required]
Uploader: Arashijind

For example, an oscilloscope might be 4U high, and rack-mountable computers are mostly between 1U and 4U high.

Category:DIN 41494

In the event of a nut being stripped out or a bolt breaking, the nut can be easily removed and replaced with a new one. Threaded mounting holes in racks where djn equipment is frequently changed are problematic because the threads can be damaged or the mounting screws can break off; both problems render the mounting hole unusable.

A third common use for rack-mounted equipment is industrial power, control, and automation hardware. By using this site, you agree to the Terms of Use and Privacy Policy. The height of the different panels will vary, The dun in the posts are arranged vertically in repeating sets of three, with center-to-center separations of 0. Thus, a 1U rackmount computer is not 1.

Portable rack cases using a rotary-molded polyethylene outer shell are a lower-cost alternative to the more durable ATA-approved case. The earliest repeaters from were installed in ad-hoc fashion on shelves, in wooden boxes and cabinets.

This page was last edited on 12 Decemberat Large server rooms will often group rack cabinets together so that racks on both sides of an aisle are either front-facing or rear-facing, which simplifies cooling by supplying cool air to the front of the racks and collecting hot air from the rear of the racks.

  GARY BRODSKY HOW TO USE THE POWERS OF DARKNESS PDF

This prevents circular airflows where hot exhaust air is recirculated through an di device and causes overheating.

A series of studies led to the adoption of frames 7 feet 2. Four-post racks allow for mounting rails to support the equipment at the front and rear. Dih posts have holes in them at regular intervals, with both posts matching, so that each hole is part of a horizontal pair with a center-to-center distance of Touring musicians, theatrical productions and sound and light companies use road case racks. End covers are typically secured with either a simple draw latch or a rotary cam “butterfly” latch, named for the shape of the twist handle.

Bell Labs Technical Journal. The amount of motion and resulting stress depends on the structural characteristics of the building and framework in which the equipment is contained, and the severity of the earthquake. This gap allows a bit idn room above and below an installed piece of equipment so it may be removed without binding on the adjacent equipment.

19-inch rack

The term relay rack appears on page at the bottom of column 1. The strength required of the mounting posts means they are invariably not merely flat strips but actually a wider folded strip arranged around the corner of the rack.

In contrast to the “inch world”, ETSI also defined the size of the rack enclosure: Two-post racks provide two vertical posts. The extra width and depth enables cabling to be routed with ease also helping to maintain bend-radius for fibre and copper cables and deeper equipment to be utilised.

The height diin a rack can vary from a few inches, such as in a broadcast console, to a floor mounted rack whose interior is 45 rack units Road cases are typically made from polyvinyl chloride PVC laminated plywood sides, joined by extruded aluminum edging, steel corners, handles and latches.

Ina durable fiber reinforced plastic inch rackmount case was 41449 by ECS Composites and became widely used in military and commercial applications for electronic deployment and operation. The cases typically use extruded aluminum bands at the ends of the body with tongue-and-groove mating to like bands for the covers.

  KOKUTAI NO HONGI PDF

There is no standard for airflow and cooling 14494 rack mounted equipment. The hole pattern thus repeats every 1. Hole spacing is 25 millimetres 0. As a result, 4-post racks have become common, with such racks featuring a mirrored pair of rear mounting posts. The rails may also be able to fully support the equipment in a position where it has been slid clear of the rack; this is useful for inspection or maintenance of equipment which will then be slid back into the rack.

inch rack – Wikipedia

Common uses include server, telecom, broadcast video, lighting, audio, and scientific lab equipment. To protect equipment from shock and vibration road rack cases use an inner and outer case. Production of clearance-hole racks is less expensive because tapping the holes is eliminated and replaced dkn fewer, less expensive, cage nuts.

Rack-mountable equipment is usually designed to occupy some integer number of U. Raised or false floor cooling in server rooms can serve a similar purpose; they permit cooling airflow to equipment through the underfloor space to the underside of enclosed rack cabinets.

Category:DIN – Wikimedia Commons

Patent 3, idn, granted June 4, Larger cases typically have wheels for easy transport. Two-post racks are most often used for telecommunication installations. The size denotes the width of the faceplate for the installed equipment. Wikimedia Foundation servers as seen from the front. Larger cases are further reinforced with additional plywood or sheet metal. George, Chassis Slide MechanismU.