ISO 15493 PDF

Purchase your copy of BS EN ISO +A as a PDF download or hard copy directly from the official BSI Shop. All BSI British. Buy EN ISO Plastics Piping Systems For Industrial Applications – Acrylonitrile-Butadiene-Styrene (Abs), Unplasticized Poly(Vinyl Chloride) (Pvc-U) . Buy ISO PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS – ACRYLONITRILE-BUTADIENE-STYRENE (ABS), UNPLASTICIZED.

Author: Sham Shaktijind
Country: Belarus
Language: English (Spanish)
Genre: Sex
Published (Last): 28 March 2008
Pages: 102
PDF File Size: 5.29 Mb
ePub File Size: 1.39 Mb
ISBN: 438-8-45065-751-8
Downloads: 59383
Price: Free* [*Free Regsitration Required]
Uploader: Kigami

Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For undated references, the latest edition of the normative document referred iiso applies. Plastics piping systems for industrial applications. Although we endeavour to maintain an up-to-date catalogue, on occasion we may not have the latest version of a document, including where it has not yet been provided through an international feed.

A version in any other language made by translation under the responsibility of a CEN member into its own language and isl to the Management Centre has the same status as the official versions. Additives shall not be used, separately or together, in quantities sufficient to impair the fabrication or solvent- cementing characteristics of the components or to impair the chemical, physical or mechanical characteristics as specified in this International Standard.

Users of British Standards should make sure that they possess the latest amendments or editions.

NOTE 2 In the case of valves, only those thermoplastics parts which are made from material conforming to this International Standard may be considered as reprocessable material. This International Standard is applicable to ABS, PVC-U or PVC-C pipes, fittings, valves and ancillary equipment, to their joints and to joints with components made of other plastics and non-plastics materials, depending on their suitability, intended to be used for the conveyance of liquid and gaseous fluids as well as of solid matter in fluids for industrial applications such as: The size of the marking shall be such that the marking is legible without magnification.

Jointing face for flat seal Jointing face with O-ring groove Figure A. If the document is revised or isi, you will be notified by email.

BS EN ISO 15493:2003+A1:2017

The components shall not contain visible impurities. Where a thread is used as a fastening thread for jointing an assembly e.

  AQIDA TAHAWIYYA ENGLISH PDF

Key dn nominal outside diameter di inside diameter of socket at midpoint of socket length L length of socket, i. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Octoberand conflicting national standards shall be withdrawn at the latest by October Metric series ISOFittings, valves and other piping system components made of unplasticized poly vinyl chloride PVC-Uchlorinated poly vinyl chloride PVC-Cacrylonitrile-butadiene-styrene ABS and acrylonitrile-styrene- acrylester ASA for pipes under pressure — Resistance to internal pressure — Test method ISOThermoplastics materials for isi and fittings for pressure applications — Classification and designation — Overall service design coefficient ISOThermoplastics materials — Preparation of tubular test pieces for the determination of the hydrostatic strength of materials used for injection moulding ISO The test shall be carried out using test pieces of pipe series S u 12,5.

Test assemblies for pressure tests shall be closed with pressuretight end-load-bearing end caps, plugs or flanges which shall be provided with connections for the entry of water and release of air. is

The main task of technical committees is to prepare International Standards. NOTE Attention is drawn to the need to take account of any relevant legislation relating to the colour coding of piping in respect of its purpose or contents for the location in which the components are intended to be used.

Pipes shall be marked at intervals of maximum 1 m, at least once per pipe. Table 1 — Isp annexes Material Annex Acrylonitrile-butadiene-styrene ABS A Unplasticized poly vinyl chloride PVC-U Ios Chlorinated poly vinyl chloride PVC-C C NOTE 2 Components conforming to any of the product standards listed in the bibliography or to national standards, as applicable, may be used with components conforming to this International Standard provided they conform to the requirements for joint dimensions and to the other relevant requirements of this standard.

For external above-ground installation, additional requirements depending on the climate shall be agreed on between manufacturer and purchaser. Components for external above-ground installations shall be adequately protected against UV radiation.

You can download and open 15943 file to your own computer but DRM prevents opening this file on another computer, including a networked server. The fitting shall be connected to the corresponding pipe in accordance with ISO 51493 not be held responsible for identifying any or all such patent rights.

  KASAMBAHAY BILL PDF

Need more than one copy? Pipes of pipe series S 5 to S 10 shall be tested at the medium level, M. Revisions British Standards are updated by amendment or revision.

EN ISO 15493:2003

The dimensions given shall be followed. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. NOTE The manufacturer is not responsible for the marking on isk component becoming illegible due to actions caused during installation and use such as painting, scratching or covering over, or the use of detergents, etc. Such systems and components are intended to be used for industrial applications above ground. If you need help with the purchase or have any queries please email enquiries standards.

They do not necessarily represent manufactured components. ISOPipe threads where pressure-tight joints are made on the threads — Part 1: Information regarding online access to British Standards via British Standards Online can be found at http: The work of preparing International Standards is normally carried out through ISO technical committees.

Attention is drawn to the fact that, for a particular test method, the technical content of the International Standard and the European Standard may be different.

DN 50 Material e. The Amber document status indicator indicates that some caution is needed when using this document – it is either: Where fittings and valves are manufactured from the same material as pipes, the material classification shall be the same as for pipes. Buying standards Orders 154993 all BSI, international and foreign standards publications should be addressed to Customer Services.

It is designed to cover every economic sector and virtually every activity of the humankind where technical standards may be used.

EN ISO – Plastics piping systems for industrial applications – Acrylo –

For the design of a piping system e. Marking shall not initiate cracks or other types of defect which adversely influence the performance of the component. It is important to us that you purchase the right document. The measurements shall not be made less than 24 h after manufacture.